98-03 4L60E 4L65E Transmission Rebuild Kit UPGRADED FOR HEAVY DUTY GM TRUCKS

Raybestos 700R4 4L60E Z-Pack High Performance 3-4 Clutch Enhancement Pack. Raybestos 4L60E High Performance Kolene Steel Module. Raybestos 700R4 4L60E Pro Series Kevlar Heavy Duty 2-4 Band. Super Heavy Duty Aftermarket Sun Gear Reaction Shell. 700R4 4L60E High Performance Corvette 2-4 Servo.

4L60E Master Bushing Kit (13 Bushings). 4L60E Master Thrust Washer Kit w/ 4 Selective Washers. High Quality Deep 4L60E Filter. 4L60E Low/ Reverse Clutch Pack.

4L60E Reverse Input Clutch Pack. Container of Soft (Blue) Assemblee Goo (16 oz). 4L60E Transmission Overhaul Kit with Lip Seals. Benefits of Precision International Overhaul Kits from Global Transmission Parts. Unlike other transmission kit manufactures, Precision Internationals overhaul kits contain parts made from high quality rubber & fiber materials.

Made in the USA to superior quality standards, which ensure the parts you will receive meet or exceed the OEM specifications. So, when you rebuild your transmission using a Precision International overhaul kit you are rebuilding your transmission to better then factory specs. Packaged friendly for the rebuilder. You wont just be receiving a bag of parts when you order one of our kits.

The parts in our kits are well packaged, which means less time wasted searching for something you think should be there that isnt. Detailed Listing of Parts this 4L60E / 4L65E Overhaul Kit Contains. Upper Valve Body Gasket, 2001-UP (OEM # 24211920).

Lower Valve Body Gasket, 2001-UP (OEM # 24211921). Valve Body Check Ball Set of 8 (OEM # 8631975).

Metal Clad Front Pump Oil Seal (OEM # 24202535). Oil Pan Gasket Cork or Farpak (OEM # 8642360). Pump Bolt O-Ring Kit (PI SUB-K3301 / OEM # 8654341).

Electrical O-Ring & Filter Seal Kit (PI SUB-K3302). Accumulator Piston O-Ring Kit (PI SUB-K3303). Piston Lip Seal Kit (PI SUB-K3304). Pump Filters & Screens (PI SUB-K3305). 2-4 Servo Inner & Outer Housing O-Ring Kit (PI SUB-K3307 / OEM #s 8642112 & 8647351). Transmission Cooler Seal & Output Shaft Snap Ring Kit (PI SUB-K33101A). Pressure Manifold Seal Kit (PI SUB-K3318). Force Motor & Shift Solenoid Filter Screen Kit (PI SUB-K33768 / OEM #s 8683768 & 8683769). 2-4 Servo Spring Kit (PI SUB-K33799A / OEM # 8654391). Upgraded TCC Regulator Valve Spring (PI SUB K-33799B). Teflon Sealing Ring Kit w/ 11 Rings (PI SUB-K33901E). Pump to Case Gasket (PI # 33702A). 2WD Extension Housing Oil Seal (PI # 8850A).

4L60E/4L65E Specific Rebuild Technical Sheets. Valve Body Check Ball Locations. Precision International is a worldwide supplier of quality products for import and domestic automatic transmissions. As well as supplying an extensive aftermarket customer base, Precision International also provides products to Original Equipment Manufacturers (OEMs).

Precision International is dedicated to providing the highest quality product that meets or exceeds the manufactures recommended specifications. This means when you use a Precision International Overhaul Kit on when rebuilding your transmission, you are using the finest rebuild kits on the market today. This 4L60E steel module has been engineered for high performance by Raybestos Powertrain. Raybestos Powertrain GM 4L60E Kolene steel clutch plates are. High quality engineered high performance products.

Kolene is a salt bath nitriding process. In generic terms, it is thermochemical diffusion process, whereby ferrous parts are processsed in molten salt with a specific nitrogen potential. Raybestos 4L60E Kolene steels provide a surface treatment that enhances wear and fatigue resistance from 200% to 500%.

Advantages of Raybestos Powertrain's 4L60E Kolene Steel Module. Enhances wear resistance 200% to 500%. Enhances fatigue resistance 200% to 500%.

When you pair this high performance steel moduel with a high energy 4L60E friction module. You are putting the highest quality parts available at one of the lowest costs found online. Listing of Frictions in the Raybestos High-Energy Friction/Clutch Pack. (5) Forward Clutches with Grooves. Takes the Heat Without Coning.

Single sided clutch system w/ the revolutionary X-32. Friction material outperforms both single-sided and double-sided original equipment clutch assemblies in torque capacity, durability and heat resistance.

7 Steps to Ultimate Clutch Performance. Use a 1988 or later input drum, identified by narrow snap ring groove and a 0.093'' 3-4 snap ring. Used only a 3-4 apply ring measuring 3.675'' +/- 0.005'' inches tall, commonly referenced as a Number 7 apply ring. This stamped steel ring rests on top of the 3-4 piston. The number'7' is stamped into the part for identification. The OEM number is 8685043. Pre-soak all friction plates in automatic transmission fluid (ATF) prior to final assembly. First, install the special grooved apply plate (bottom) with the groove facing upward.

Do not attempt to install the narrow external spline friction plate, with "TOP" printed on it, into the machined groove. Set it aside until Step 6. Install the friction plates, beginning with an external spline friction plate with friction material facing upward (away from the special grooved apply plate), then an internal spline friction plate with friction material facing upward, continue alternating until you have installed seven external spline friction plates and seven internal spline friction plates.

Install the special external spline friction plate, identified by the narrow band of friction material, with the word "TOP" facing up. This eternal spline plate does not look like any of the others. It is critical to install this plate last. NOTE: Use of load release springs is optional. Use of load release springs recommend for RPM above 5000.

145'' pressure plate provided, followed by the factory snap ring. Clearance should be within the 0.050''-0.07'' range.

If not, install optional external spline shim to adjust clearance to 0.050''-0.070'' if necessary. It is recommenced to check actual piston travel by placing a dial indicator on the backing plate and apply air to the third clutch feed.

If clearance is measured with feeler gauges, it is important to measure in two places at the same time, 180 degrees apart, for even loading of the pressure plate. Failure to do so may cause incorrect end play reading. 2-4 Band, Raybestos, Pro Series High Energy, 700R4/4L6OE/4L65E (1987-Up). With a Pro Series High Energy 2-4 Band for a 700R4/4L60E/4L65E made by Raybestos, you know you have nothing to worry about.

Friction coating has been proven to. Than the OEM 2-4 band. This means you can rest easy knowing that inferior parts aren't going to cut your rebuilt transmissions life short. The Pro Series 2-4 Band paired with a Corvette Servo Assembly by OMS, LLC, item #. , makes for a high performance combination that will speed your shifts up dramatically! Higher co-efficient of friction competitors' high-energy bands. Heat-treated anchors for added strength on specific applications.

Resistance to extreme heat (up to 700º F). A significant increase in durability.

Stable when exposed to high-energy conditionas. Affordable performance for every rebuild. Reduced risk of overheating steel plates. This is an extra heavy duty washer style sun shell that is an aftermarket upgrade over the OEM sun shell in GM's 700R4 and 4L60E transmissions. The OEM 700R4/4L60E sun shell is a weak point in the transmission and is recommended to be upgraded on the rebuild. Global Transmission Parts specializes in providing high-performance GM automatic transmission parts. We service a wide customer base that ranges from professional remanufactures to the casual rebuilder. Our Central Ohio location gives us the ability to provide one day standard ground parcel service to all of.

West Virginia, plus parts of. The entire East Coast, Great Plains states and. Please be prepared to provide photos of the damaged item and packaging for us to submit to the carrier. So, we work hard finding the best rate for your situation and charge you what we are being charged. The item "98-03 4L60E 4L65E Transmission Rebuild Kit UPGRADED FOR HEAVY DUTY GM TRUCKS" is in sale since Saturday, July 16, 2016.

This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Transmission & Drivetrain\Transmission Rebuild Kits". The seller is "globaltransmissionparts" and is located in Circleville, Ohio. This item can be shipped worldwide.

Brand: RAYBESTOS, PRECISION INTERNATIONAL
Manufacturer Part Number: KP33900EF, STMGM07K